Telcobridges - Session Border Controllers
Would you like to react to this message? Create an account in a few clicks or log in to continue.

What logging I need to enable to see the User-to-User data on the ProSBC server.

Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 6:43 am

Hello,

We are testing a new trunk that uses User-to-User data in the transfer. I can see from my IVR that I am passing the User-to-User in the refer but wanted to know what logging I need to enable to see the same data on the ProSBC server to make sure it is being passed correctly.

I see the following in the toolpack-engine log file:


06th, 19:36:36.418+0000 TBLV2 ENGI: Sip  0xFFF7DCB9 (0xA15FAB3D) |  -> CmcNotifEventCallError: Data path errors detected
06th, 19:36:36.687+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | StoreExtraNumber: 0-UUI purpose parameter= noa=0
06th, 19:36:36.687+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | StoreExtraNumber: 1-UUI content parameter= noa=0
06th, 19:36:36.687+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | SIPExtractParams: Contact host = '172.31.50.11:5060'
06th, 19:36:36.687+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | StoreExtraNumber: 2-Contact host=172.31.50.11:5060 noa=0
06th, 19:36:36.687+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | StoreExtraNumber: 3-Sip header=Referred-By:<sip:4388006242> noa=0
06th, 19:36:36.687+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | StoreExtraNumber: 4-Request URI=sip:4388006242@172.31.50.15:5060 noa=0
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | SIPExtractParams: Refer-To host = '172.31.50.15:5060'
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) | StoreExtraNumber: 5-Refer-To host=172.31.50.15:5060 noa=0
06th, 19:36:36.688+0000 TBLV2 ENGI: CallBridgingSampleSipHandleNotifIncomingRefer: Received refer for library: ip-172-31-50-15.ec2.internal.SIP_CTRL_VOIP0_TS:  
06th, 19:36:36.688+0000 TBLV2 ENGI:  Refer-to : sip:13155550029@172.31.50.15:0.
06th, 19:36:36.688+0000 TBLV2 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> CmcNotifCallTransferRequest Number=13155550029
06th, 19:36:36.688+0000 TBLV2 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> FillGenericHeader: Call contains UUI of size 66 bytes
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> FillGenericHeader: 0-UUI purpose parameter=
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> FillGenericHeader: 1-UUI content parameter=
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> FillGenericHeader: 2-Contact host=172.31.50.11:5060
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> FillGenericHeader: 3-Sip header=Referred-By:<sip:4388006242>
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> FillGenericHeader: 4-Request URI=sip:4388006242@172.31.50.15:5060
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> FillGenericHeader: 5-Refer-To host=172.31.50.15:5060
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Protocol:SIP  NotifCallTransferRequest
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_FROM  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_TO  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_CALLID  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_CSEQ  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_VIA  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_REQ_REFERTO  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_REQ_MAXFORWARDS  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_SUPPORTED  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_EXTENSION User-To-User: 0055555f5075626c69636174696f6e3d457567656e653b55555f43726d3d3b55555f47726f75703d456e746572706973653b55555f546f633d4e65775f5374617274;encoding=hex
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_CONTACT  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_ALLOW  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_ALLOW_EVENTS  
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_GEN_EXTENSION Referred-By: <sip:4388006242>
06th, 19:36:36.688+0000 TBLV1 ENGI: Sip  0xFFBDE492 (0x215FAB41) |  -> Headers type=HEADER_TYPE_ENT_CONTENTLENGTH  


Best Regards,


Last edited by ahsanul.moyeen on Thu May 27, 2021 7:25 am; edited 1 time in total

Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 6:47 am

Hi,

The best way to verify this is to take a SIP capture of the call and check the Inbound Invite and outbound Invite messages.

You can do this with tbsigtrace:
. ssh to the SBC
. tbsigtrace -sip and enter
. do the test call
. press q to quit
. find the .cap file at /mnt/.0/tb/toolpack/setup/12358/3.1/apps/tbsigtrace

Please follow: Toolpack_Debug_Application:Tbsigtrace

Best Regards,

Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 7:24 am

However, I did see something slightly odd in it.

In the refer it has:
User-To-User: 0055555f5075626c69636174696f6e3d457567656e653b55555f43726d3d3b55555f47726f75703d456e746572706973653b55555f546f633d4e65775f5374617274;encoding=hex
In the invite to the destination is has:
User-To-User: %00UU_Publication%3DEugene%3BUU_Crm%3D%3BUU_Group%3DEnterpise%3BUU_Toc%3DNew_Start;encoding=text;purpose=isdn-interwork;content=isdn-uui
Is it converting it on the invite?

Best Regards,

Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 7:26 am

Hi,

I see the incoming UUI is in Hex mode, while ProSBC is using Text mode.
You can change it via Webportal -> SIP -> Advanced parameters : User-to-User encoding

What logging I need to enable to see the User-to-User data on the ProSBC server. 411

Please follow: Parameter:_SIP:_User-to-User_encoding


Best Regards,


Last edited by ahsanul.moyeen on Thu May 27, 2021 8:10 am; edited 1 time in total

Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 8:03 am

Hello,
I have one customer that I send the data for the User-to-user using Hex and another that I am sending via Text. What would I need to do to differentiate the 2?

Best Regards,

Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 8:04 am

Hi,

You can create two profiles, one for Hex, and another for Text and assign them to the 2 NAPs accordingly.

Best Regards,

Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 8:04 am

Hello,

I am looking through the options and I don't see the user-to-user settings. Can you send me a screenshot of where it is?

Best Regards,

Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Guest Thu May 27, 2021 8:08 am

Hi,

Webportal -> SIP -> Advanced parameters : User-to-User encoding

What logging I need to enable to see the User-to-User data on the ProSBC server. 5_010
What logging I need to enable to see the User-to-User data on the ProSBC server. 510



Best Regards,


Guest
Guest


Back to top Go down

What logging I need to enable to see the User-to-User data on the ProSBC server. Empty Re: What logging I need to enable to see the User-to-User data on the ProSBC server.

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum